Fridge with
Freezer Compartment
TSM 1541
TSM 1541P
Operating instructions
1 Your refrigerator
2 Warnings
Electrical Requirements .....................6
Warning! This Appliance Must Be
4
5
4 Before operating
Final Check .....................................13
13
5 Using your refrigerator 14
Temperature Control And
Adjustment......................................14
Defrosting........................................15
Earthed .............................................6
Energy Saving Tips............................7
6 Maintenance and
3 Installation
Points to be considered when re-
8
cleaning
18
19
transporting your refrigerator .............8
Before operating your refrigerator ......8
Electric connection ............................8
Disposing of the packaging ...............9
Disposing of your old refrigerator .......9
Placing and Installation ......................9
Reversing The Doors .......................10
7 Do's and Don'ts
8 How To Obtain Service 20
9 Guarantee Details 21
EN
3
1 Your refrigerator
Congratulations on your choice of a BLOMBERG quality Appliance which has
been designed to give you service for many years.
13
8
1
2
3
10
9
3
4
5
6
11
12
7
1.
2.
3.
4.
5.
6.
7.
Freezing compartment & ice tray
Interior light -Thermostat knob
Movable shelves
Defrost water collection channel-Drain tabe
Crisper cover
8.
9.
Dairy compartment
Door shelves
10. Eggy tray
11. Bottle shelf
12. Bottle gripper
13. Top trim
Crisper
Adjustable front feet
C Figures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.
EN
4
2 Warnings
• To obtain the best possible
•DO NOT connect your appliance to
the electricity supply until all packing
and transit protectors have been
removed.
• Leave to stand for at least 4
hours before switching on to allow
compressor oil to settle if transported
horizontally.
performance and trouble free operation
from your appliance it is very important
to carefully read these instructions.
• On delivery, check to make sure that
the product is not damaged and that
all the parts and accessories are in
perfect condition.
• Ensure that the plug remains readily
accessible. Do not use multiple
adapter or extension cable.
• Failure to observe these instructions
may invalidate your right to free service
during the guarantee period.
• If you are discarding an old
refrigerator with a lock or latch fitted
to the door, disable the lock/latch,
ensure that it is left in a safe condition
to prevent the entrapment of young
children.
• This fridge/freezer must only be used
for its intended purpose i.e the storing
and freezing of edible foodstuff.
• Do not dispose of the appliance on
a fire. At BLOMBERG, the care and
protection of our environment is an
ongoing commitment. This appliance
which is among the latest range
introduced is particularly environment
friendly. Your appliance contains non
CFC / HFC natural substances in the
cooling system (Called R600a) and in
the insulation (Called cyclopentane)
which are potentially flammable
if exposed to fire. Therefore, take
care not to damage, the cooling
circuit / pipes of the appliance in
transportation and in use. In case of
damage do not expose the appliance
to fire or potential ignition source and
immediately ventilate the room where
the appliance is situated.
• Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction.
• Do not use mechanical devices
or other means to accelerate the
defrosting process, other than those
recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances
inside the food storage compartments
of the appliance, unless they are
of the type recommended by the
manufacturer.
• We suggest you keep these
instructions in a safe place for easy
reference.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to
ensure that they do not play
• We suggest you contact your local
authority for disposal information and
facilities available.
• See Installation Instructions on on
page 9 for information on suitable
location.
with the appliance.
EN
5
Important! Fitting A Different Plug
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals in
your plug proceed as follows: (See
diagram).
Electrical Requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown on the rating
plate inside the appliance corresponds
to your electricity supply.
Rating label is on the left hand side of
fridge inner liner.
1. Connect the green-yellow or green
(Earth) wire to the terminal in the plug
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket.
The appliance must be positioned so
that the plug is accessible.
Should the mains lead of the appliance
become damaged or should it need
replacing at any time, it must be
replaced by a special purpose made
mains lead which can only be obtained
from a BLOMBERG Authorised Service
Agent.
marked ‘E’ or with the symbol
or
coloured green and yellow or green.
2. Connect the blue (Neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3. Connect the brown (Live) wire to
the terminal in the plug marked ‘L’ or
coloured red.
With alternative plugs a 13 A fuse must
be fitted either in the plug or adaptor
or in the main fuse box. If in doubt
contact a qualified electrician.
Warning! This Appliance
Must Be Earthed
If the fitted moulded plug is not
suitable for your socket, then the plug
should be cut off and an appropriate
plug fitted. Destroy the old plug which
is cut off as a plug with bared cord
could cause a shock hazard if inserted
into a socket elsewhere in the house.
The moulded plug on this appliance
incorporates a 13 A fuse. Should
the fuse need to be replaced an
6mm.
GREEN &
YELLOW
OR
GREEN
L
BROWN
OR
RED
N
22mm.
BLUE
OR
BLACK
ASTABEAB approved BS 1362 fuse
of the same rating must be used. Do
not forget to refit the fuse cover. In the
event of losing the fuse cover the plug
must not be used until a replacement
fuse cover has been fitted. Colour
of the replacement fuse cover must
be the same colour as that visible on
the pin face of the plug. Fuse covers
are available from any good electrical
CORD GRIP
store.
EN
6
Energy Saving Tips
1- Ensure your appliance is installed in
a well ventilated area.
2- Ensure the time between buying
chilled/frozen food and placing them
in your appliance is kept at minimum,
particularly in summer. We recommend
you use a cool bag or a special carrier
bag to carry frozen food.
3- Do not leave the door (s) of your
appliance open longer than necessary
and ensure they are closed properly
after each opening.
4- Defrost frozen food in the fridge, so
that frozen food acts as an ice pack to
assist cooling in fridge.
EN
7
3 Installation
BPlease remember that the
manufacturer shall not be held liable if
the information given in the instruction
manual is not observed.
Points to be considered
when re-transporting your
refrigerator
1
2
3
1
3
3
1.Your refrigerator must be emptied and
cleaned prior to any transportation.
2.Shelves, accessories, crisper and etc.
in your refrigerator must be fastened
securely by adhesive tape against any
jolt before repackaging.
3.Packaging must be tied with thick
tapes and strong ropes and the
rules of transportation printed on the
package must be followed.
3.Clean the interior of the refrigerator as
recommended in the “Maintenance
and cleaning” section.
4.Plug the refrigerator into the wall outlet.
When the fridge door is open, the
fridge compartment interior light will
come on.
5.You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
even if the compressor is not running
and this is quite normal.
6.Front edges of the refrigerator may feel
warm. This is normal. These areas
are designed to be warm to avoid
condensation
Please do not forget…
Every recycled material is an
indispensable source for the nature
and for our national resources.
If you wish to contribute to recycling
the packaging materials, you can
get further information from the
environmental bodies or local
authorities.
Electric connection
Before operating your
Connect your product to a grounded
socket which is being protected by a
fuse with the appropriate capacity.
Important:
refrigerator
Before starting to use your refrigerator
check the following:
1.Is the interior of the refrigerator dry and
can the air circulate freely in the rear
of it?
• The connection must be in compliance
with national regulations.
• The power cable plug must be easily
accessible after installation.
• The specified voltage must be equal to
your mains voltage.
• Extension cables and multiway plugs
must not be used for connection.
2.Please install the 2 plastic wedges
as illustrated in the figure. Plastic
wedges will provide the required
distance between your refrigerator
and the wall in order to allow the air
circulation. (The illustrated figure is
only an example and does not match
exactly with your product.)
BA damaged power cable must be
replaced by a qualified electrician.
EN
8
in order to achieve an efficient
operation. If the refrigerator is to be
placed in a recess in the wall, there
must be at least 5 cm distance with
the ceiling and at least 5 cm with
the wall. If the floor is covered with
a carpet, your product must be
elevated 2.5 cm from the floor.
4. Place your refrigerator on an even floor
surface to prevent jolts.
BProduct must not be operated before
it is repaired! There is danger of
electric shock!
Disposing of the packaging
The packing materials may be
dangerous for children. Keep the
packing materials out of the reach
of children or dispose of them by
classifying them in accordance
with the waste instructions. Do not
dispose of them along with the normal
household waste.
The packing of your refrigerator is
produced from recyclable materials.
Disposing of your old
refrigerator
Dispose of your old refrigerator without
giving any harm to the environment.
•You may consult your authorised dealer
or waste collection center of your
municipality about the disposal of
your refrigerator.
Before disposing of your refrigerator, cut
out the electric plug and, if there are
any locks on the door, make them
inoperable in order to protect children
against any danger.
Placing and Installation
A If the entrance door of the room
where the refrigerator will be
installed is not wide enough for the
refrigerator to pass through, then call
the authorised service to have them
remove the doors of your refrigerator
and pass it sideways through the
door.
1. Install your refrigerator to a place that
allows ease of use.
2. Keep your refrigerator away from heat
sources, humid places and direct
sunlight.
3. There must be appropriate air
ventilation around your refrigerator
EN
9
1. Switch off the appliance at the
socket outlet and pull out the mains
plug.
2. Remove all food, loose items and
fittings from inside the appliance and
door shelves.
3. Carefully tilt the appliance on
its back side. (1) (You may need
somebody to help you.) Take care not
to damage the appliance by laying
on some protective material (e.g. its
original packaging). Make sure that
you tilt the appliance on its back side,
otherwise compressor oil may block
the pipes and you may damage the
appliance.
Reversing The Doors
We recommend that you reverse doors
before switching on for the first time.
Tools required: Small and medium size
flat and cross-headed screwdrivers, a
pair of pliers.
Spare Parts supplied in the plastic
bag: The following parts, which are
exclusively for left hand side fitted
hinge operation are supplied in a
plastic bag with the appliance:
- Upper door top trim hinge covers –
there are 2 different parts, one for each
side of top trim.
- Upper door middle hinge bushing/
door stopper assembly.
4. Unscrew and remove the LHS front
feet and bolt (2).
5. Unscrew the bolts and remove the
bottom hinge while holding the door
(3).
6. Remove the door carefully from the
top hinge by sliding down wards (4).
7. Reposition top hinge bushing and
blanking plug on the opposite side and
stand the door safely (5). You may find
it easier to remove the bushing and the
plug with the tip of a small screwdriver.
Take care not to mark the door.
8. Remove the two screws from the
top front plastic trim (6)
9. Remove the bushing of the four-
star compartment cover hinge(7); Pull
out the cover (8) and remove pin on
the upper wall (9) Remove the locking
mechanism (10)
We suggest you keep all the parts
supplied in the plastic bag and also
parts, which have been removed when
reversing doors, in a safe place for
possible future, re-use.
IMPORTANT: We suggest you ask
somebody to help you when moving
the appliance around and to hold
doors when removing / re-fitting
hinges and doors to avoid any injury
and damage to the product.
Please refer to diagrams supplied. To
follow numbers in brackets below,
refer to the main diagram.
10. Remove the two screws from the
back of the top plate (11) and remove
the top plate (12)
11. Remove the top hinge and re-
position it on the opposite side (13)
EN
10
12. Re-fit the top plate (14) and put the
two screws into the top front plastic
trim (15)
13. Put the two screws back into the
top plate (16)
17. Fit the other front feet (25).
18. Carefully stand your appliance.
(You may need somebody to help you.)
Adjust the front feet (See
Installation Instructions)
14. Put the pin on the upper wall
(17). Take the 4-star compartment
cover(18). Put the hinge (19) and the
locking mechanism in place (20). Put
the caps in to the holes (21&22)
15. To refit the door, locate the top
hinge in the door, attach to the cabinet
and hold the door (23).
16. Fit the bottom hinge (24). If
necessary adjust and then tighten the
bolts. Ensure, that the door opens
and closes easily and that there are
no gaps allowing air into the cabinet. If
there are gaps between the door seal
and the cabinet, adjust the door seal
by gently pulling away from the door
using fingers.
19. Put back all, loose items and
fittings.
20. Wait for at least 4 hours to allow
the system to settle before switching
on.
Spare plastic parts supplied with
the appliance are for your future use
during door repositioning.
21. Fit the door handle to the opposite
side of the door and tighten
the bolts. (26).
EN
11
13
11
11
12
6
9
1
6
7
10
8
4
60°
5
3
2
16
16
14
20
17
15
1
15
21
22
19
18
60°
23
25
26
24
EN
12
4 Before operating
7. We recommend that you set the
thermostat knob at 3 (three) and
monitor the temperature to ensure
the appliance maintains desired
storage temperatures (See section
Temperature Control and Adjustment).
8. Do not load the appliance
Final Check
Before you start using the fridge/
freezer check that:
1. The feet have been adjusted for
perfect levelling.
immediately it is switched on. Wait
until the correct storage temperature
has been reached. We recommend
that you check the temperature
with an accurate thermometer (see;
Temperature Control and Adjustment).
Important Note :Ice formation at the
back is normal, do not worry. (See
Defrosting)
2. The interior is dry and air can
circulate freely.
3. Clean the interior as recommended
under “CLEANING AND CARE.”
4. Insert the plug into the wall socket
and switch on the electricity supply.
When the door is open the interior light
will come on.
5. You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
whether the compressor is running or
not which is quite normal.
6. Slight undulation of the top of the
cabinet is quite normal due to the
manufacturing process used, so do
not worry, it is not a d efect.
EN
13
5 Using your refrigerator
Temperature Control And Adjustment
Operating temperatures are controlled by the thermostat (see diagram). Settings
may be made from 1 to 5, the coldest position.When the appliance is switched
on for the first time, the thermostat should be adjusted so that after 24 hours, the
average fridge temperature is no higher than +5°C (+41°F ).We recommend you
set the thermostat halfway between the 1 and 5 setting and monitor to obtain the
desired temperature i. e. towards 5 you will obtain a colder fridge temperature and
vice versa. Some sections of the fridge may be cooler or warmer ( such as the
salad crisper and the top part of the cabinet ) which is quite normal.Over ambient
temperatures of 25°C (77°F) especially in summer turn the thermostat knob towards
5. Under ambient temperatures of 25°C (77°F) turn the thermostat knob to a half
way position.Frequent door opening cause higher internal temperatures, so close
the door as soon as possible after use.In case of a temporary ice build up in the
fridge compartment reduce the thermostat setting to 1, monitoring at the same time
that the fridge temperature is maximum +5 degrees C (41 degrees F). Once the ice
build up disappears and the appliance starts auto defrosting again as normal, then
you may increase the thermostat setting, if required.
Suggested Arrangement Of Food In The Fridge
Arrangement Examples (See diagram).
1. To freeze fresh food, frozen food, rapid cooling of beverages,
making ice cubes.
2. Baked, chilled cooked food, dairy products,
3. Meat, sausages, cold cuts, cans.
4 .Fruit, vegetables, salads.
5. Tubes, small bottles and cans.
6. Butter, cheese, dairy products..
7. Beverages, large bottles.
The following guidelines and recommendations are suggested to obtain the best
results and storage hygiene.
1. The freezer compartment is
storage of pre frozen food. The recommendation for
the food packaging should be observed at all times.
rated and suitable for the freezing and
storage as stated on
2. The fridge is for the short term storage of fresh food and drinks.
3. Cooked dishes must be stored in airtight covered containers and are best placed
on either of the removable shelves.
4. Fresh wrapped produce can be placed on the shelf. Fresh fruit and vegetables
should be cleaned and stored in the crisper bins.
EN
14
1
5
2
6
2
3
4
7
5. Bottles can be placed in the door
section.
11. Some fruit and vegetables suffer
damage if kept at temperatures near
0 degrees centigrade. Therefore
wrap pineapples, melon, cucumbers,
tomatoes and similar produce in
polythene bags.
12. Shelves, racks, crisper bins, dairy
compartments, drawers, baskets
trays, flaps, bottle grippers are all
removable.
6. To store raw meat, wrap in
polythene bags and place on the
lowest shelf. Do not allow to come
into contact with cooked food to avoid
contamination. For safety, only store
raw meat for two to three days.
7. Shelves incorporate rear stops and
tilting for storing bottles. Lift shelf to
clear grooves when adjusting.
8. To tilt a shelf place the back of
the shelf one level below the front of
the shelf. To remove a tilted shelf, first
release the back off the grooves and
then pull it.
13. Always wrap food using a suitable
packaging material before storing in
your
appliance to avoid contact
with the appliance surface and food
remains for
hygiene reasons.
9. Keep the food packed, wrapped
or covered. Allow hot food and
Defrosting
A) Fridge compartment
beverages to cool before placing them The fridge defrosts automatically.
in the fridge. Do not store explosive
substances in the refrigerator. High
proof alcohol must be stored upright
in sealed containers. Left over canned
food should not be stored in the can.
10. Fizzy drinks should not be frozen
and products such as flavoured water
ices should not be consumed too cold.
The defrosting water runs to the drain
tube via a collection channel and is
evaporated in a special container at
the back of the appliance
During defrosting, water droplets may
form at the back of the fridge where
a concealed evaporator is located.
EN
15
Some droplets may remain on the
liner and refreeze when defrosting is
completed. Do not use pointed or
sharp-edged objects such as knives
or forks to remove the droplets which
have refrozen.
If, at any time, the defrost water does
not drain from the collection channel,
check that no food particles have
blocked the drain tube. The drain tube
can be cleared by pushing the special
plastic plunger provided down the
drain tube.
B) Freezer compartment
Defrost twice a year or when a frost
layer of around 7 mm (1/4”) has
formed.
To start defrosting procedure switch off
the appliance at the socket outlet and
pull out the mains plug.
All food should be wrapped in several
layers of newspaper and stored in a
cool place (e.g. fridge or larder).
Containers full of warm water may be
placed carefully in the freezer to speed
up the defrosting.
2
1
EN
16
REPLACING THE INTERIOR LIGHT
BULB (See diagram)
Should the light fail to work switch
off at the socket outlet and pull out
the mains plug. Follow the below
instructions to check if the light bulb
has worked itself loose.
If the light still fails to work obtain a
replacement E14 screw cap type
15 Watt (Max) bulb from your local
electrical store and then fit it as
follows:
1. Switch off at the socket outlet and
pull out the mains plug. You may find
it useful to remove shelves for easy
access.
2. Remove the light diffuser cover as
shown in figure (b-c).
3. Replace the burnt-out light bulb.
4. Reassemble the light diffuser cover
as shown in figure (d).
“Push firmly to ensure cover is fitted
properly.”
5. Carefully dispose of the burnt-out
light bulb immediately.
“Replacement light bulb can easily be
obtained from a good local electrical or
DIY store.”
EN
17
6 Maintenance and cleaning
** We recommend that you switch
off the appliance at the socket outlet
and pull out the mains plug before
cleaning.
** Any dust that gathers on the
condenser, which is located at
the back of the freezer, should be
removed once a year with a vacuum
cleaner.
** Never use any sharp abrasive
instrument, soap, household cleaner,
detergent and wax polish for cleaning.
** Check door seals regularly to ensure
they are clean and free from food
particles..
** Use luke warm water to clean the
cabinet of the appliance and wipe it
dry.
** Never :
Clean the worktop with unsuitable
material; eg petroleum based
products.
Subject it to hot temperatures in
any way, Scour, rub etc., with abrasive
material.
** Use a damp cloth wrung out
in a solution of one teaspoon of
bicarbonate of soda to one pint of
water to clean the interior and wipe it
dry.
** Excess deposit of ice should be
removed on a regular basis using
the handle of a spoon. Large
accumulation of ice will impair the
performance of the freezer.
** If the freezer is not going to
be used for a long period of time
switch it off,remove all food,
clean it and leave the door ajar.
** To remove a drawer, pull it
as far as possible, and then tilt
it upwards, and then pull it out
completely.
EN
18
7 Do's and Don'ts
Don’t- Consume food which has been
stored for an excessive time in the
larder refrigerator.
Don’t- Consume food which has been
stored for an excessive time in the
larder refrigerator.
Don’t- Store cooked and fresh food
together in the same container.
They should be packaged and
stored seperately.
Don’t- Let defrosting food or food
juices drip onto food in your larder
refrigerator.
Do- Clean your appliance regularly
(See “Cleaning and Care”)
Do- Keep raw meat and poultry below
cooked food and dairy products.
Do-Keep food for as short a time
as possible and adhere to ‘Best
Before’ and “Use By” dates.
Do- Take off any unusable leaves on
vegetables and wipe off any soil.
Do- Leave lettuce, cabbage, parsley
and cauliflower on the stem.
Do- Wrap cheese firstly in greaseproof
paper and then in a polythene bag
excluding as much air as possible.
For best results take out of the
fridge compartment an hour before
eating.
Do- Wrap raw meat and poultry
loosely in polythene or aluminium
foil. This prevents drying.
Do- Wrap fish and offal in polythene
bags.
Do- Wrap food which have a strong
odour or can dry out in polythene
bags, aluminium foil or place in an
airtight container.
Do- Wrap bread well to keep it fresh.
Do- Chill white wines, beer, lager and
mineral water before serving.
Don’t- Store bananas in your fridge.
Don’t- Store melon in your fridge. It
can be chilled for short periods as
long as it is wrapped to avoid it
flavouring other food.
PROBLEM SOLVING
If the appliance does not operate when
switched on, check whether:
• The plug is inserted properly in the
socket and that the power supply is
on. (To check the power supply to the
socket, plug in another appliance)
• The fuse has blown/circuit breaker
has tripped/main distribution switch
has been turned off.
• The temperature control has been
set correctly.
• New plug is wired correctly if you
have changed the fitted moulded plug.
If the appliance is still not operating
after the above checks, please refer
to the section on “How To Obtain
Service”.
Please ensure that above checks have
been made as a charge will be made if
no fault is found.
Don’t- Leave the door open for long
periods as this will make the larder
refrigerator more costly to run.
Don’t- Don’t- Store poisonous or any
dangerous substances in the larder
refrigerator. Your larder refrigerator
has been designed for the storage
of edible foodstuffs only.
EN
19
8 How To Obtain Service
Please keep your purchase receipt or other proof of purchase in a safe place;
you will need to have it should the product require attention under guarantee.
You should also complete the details below; it will help us assist you when
requesting service. (The model number is printed on the Instruction Booklet and
the serial number is printed on the Rating Label affixed to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number
below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas & Dual Fuel Cookers
Washing Machines & Dishwashers
0845 6046859
0845 6046859
0845 6046859
0845 6046859
Republic of Ireland
All Refrigeration, All Cookers
01 862 3411
Washing Machines & Dishwashers
Before requesting service please check the trouble-shooting guide in the
Operating Instructions as a charge may be levied where no fault is found even
though your product may still be under guarantee.
EN
20
9 Guarantee Details
Your new BLOMBERG product is guaranteed against the cost of breakdown
repairs for three years from the date of the original purchase.
What is covered?
• Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
• The cost of functional replacement parts, but excluding consumable items.
• The labour costs of a BLOMBERG approved repairer to carry out the
repair.
What is not covered?
• Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including knobs, flaps, handles or container lids.
• Accessories or consumable items including but not limited to, ice trays,
scrapers, cutlery baskets, filters and light bulbs.
• Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
• Repairs to products used on commercial or non-residential household
premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is often
included within your household contents insurance policy, or may be available
separately from your retailer).
Important notes.
• Your BLOMBERG product is designed and built for domestic household
use only.
• The guarantee will be void if the product is installed or used in commercial or
non-residential domestic household premises.
• The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Installer is
recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a Gas Safe (or BORD GAIS) registered
Gas Installer.
• The guarantee is given only within the boundaries of the United Kingdom and
the Republic of Ireland.
• The guarantee is applicable only to new products and is not transferable if the
product is resold.
BLOMBERG disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
EN
21
Blomberg, 36-38 Caxton Way, Watford, Hertfordshire, WD18 8UF
Tel: 0845 6048340 Fax: 0845 6004922
48 8257 0000/AG
|